Trunk between cisco and unifi switch. 168. if I have two same switches and I connect both of them with 3 cables through 25G ports, will that work, if it does will it improve the speed between two switches or will it create loops and network will crash? Thanks It is built around the Unifi product line, but does include helpful information if you use an diffferent brand managed switch. Good so far. make sure both the switches have same VLAN created and participated in STP. In this post, I’ll go through how to configure VLANs on UniFi switches, specifically focusing on the USW-Pro-Max-16 and USW-Lite-8 models. I'm going to write them in Cisco switch CLI format, as that is the most understandable I believe: "All" port profile (always exists, default for ports on a new device): - switchport mode trunk - switchport trunk native vlan 1 (this is the default if you haven't changed the native VLAN on a cisco switch) The . Of course on the UBNT side, it isn't that simple for some reason. 0/24 network. Block All (Access Port): This option only permits traffic to pass on the Native (Untagged) VLAN. Note that wireless clients can connect to the inside VLAN (100/native), SSID "Ramsey", pull an IP, and utilize the network The Cisco switch is configured as a trunk with native vlan 35, allowing (tagging) all other vlans. On this as well I have a seperate VLAN55 with a seperate 192. Link to How To Create VLANs and Firewall Rules: • NEW to UNIFI VLANs?? Nov 25, 2021 · The management vlan HAS to be tagged with unifi access points. 55. ! interface GigabitEthernet1/0/35 description WAP switchport trunk allowed vlan 49,75,95,99 switchport trunk native vlan 49 switchport mode trunk ! Unifi has "port profiles", some are auto-generated and then you can make custom ones. Hurray for open networking standards! Oct 9, 2024 · On the SPAN, I don’t see any traffic at all on VLAN 25. Mar 1, 2024 · Trunk Between 3750-X Switches - both the switches 3750X and one of the switch you have Meraki AP connected is this correct. I have succesfully kinda trunked a port on the US-48-500W for my testing AP, connecting two different VLAN’s for my Jul 12, 2019 · All of the switches are Cisco. Trying to add a Unifi switch and another Ubiquiti AP. When you trunk between 2 devices always suggest to match the config both the sides including native VLAN best practice to get optimal outcome. UniFi and Cisco (or any other network vendor) can work together. The Core is doing L3 routing for four VFR‘s. Network Theory starts on July 26! Check out this video on how to make a trunk between a Cisco switch and a UniFi Switch!! Call me for a friendly chat on my test number: 309-857-0188. ASA > Catalyst > Unifi switch > Ubiquiti AP The trunk port from the Catalyst to Unifi switch looks like this: switchport trunk native vlan 6 switchport trunk allowed vlan 1,6,50 switchport mode trunk Vlan 6 works fine (internal Wi-Fi). Recently replaced all Cisco APs with Ubiquiti. Other VFR‘s are routed on the F We would like to show you a description here but the site won’t allow us. We would like to show you a description here but the site won’t allow us. Aug 3, 2024 · Hey I was wondering if anyone here has done VLAN trunking between Ubiquiti and Cisco Switches? I currently have access to a C2960X-48TS-LL & US-48-500W swithches, and I would like to try to learn how to configure port trunking properly between the two different OEMs solutions. Vlan 49 is my management vlan in the below example. Ubiquiti equipment requires that trunks be configured with a native VLAN that has access to the Unifi controller in order to provide status and receive updates. So the management vlan needs to be the native vlan on the switch. The setup is the following: Two Catalyst 9300 Core switches in stack. Allow All (Trunk Port): By default, UniFi switch ports allow traffic from all VLANs created in UniFi. Custom (Trunk Port): This option can be used to allow traffic for subset of VLANs, rather than all of them. The stack is connected to two Secure Firewalls 3105. Vlan 50 does May 9, 2021 · How to configure a UniFi network to work with a layer 3 Cisco switch. Sep 17, 2024 · Hello, I am asking myself what others recommend for the connection between core switch and Firewall. May 17, 2025 · The way VLANs are configured on UniFi switches is slightly different from what I was used to. What is your Unifi VLAN config>? deannawetzel (Deanna4500) April 23, 2022, 11:31am 4 Jan 26, 2022 · Switch Pro Aggregation from UniFi has 4 ports with 25G. Apr 21, 2022 · On your switch port you said you have the following config switchport trunk native vlan 5 switchport trunk allowed vlan 1,5,10,15,20 That means that your Unifi AP should also have those VLAN’s configured so it is aware of them. Jun 26, 2019 · Hello i have a configured a trunk port between a Cisco and a DELL powerconnect however i cannot pass traffic the Blue is CISCO the Orange is DELL What did i mis-configure? Native VLAN is 20 for DATA Jun 27, 2020 · UniFi gateway WiFi access point connected on LAN1 of this port with POE Injector. grn fqyuc gahjxry cqkbb ievm kvecr mtgwwb pzm ujm woydmeu